Floor Sourcing Services
Home Advisor bamboo Floor Products Bamboo Flooring - Stained brushed on edge

Bamboo Flooring - Stained brushed on edge

Have A Question?
  • bamboo Floor Products Detail


 

Hand scrap surface with light brushed

 

 

Stained brushed one edge


 

Three different width size, looks more nature

 

Density: 1050kg/m3




    


A free consultation

We focus on floor inspections only, we try to help you to solve all the questions in flooring line.

Related Products

Outdoor Floor Outdoor Floor

Carbonized Vertical Bamboo Decking

Solid Bamboo Decking, Vertical Size: length:1960-6000mm; Width:90-200mm; Thickness: 18mm

bamboo walls construction bamboo walls construction

Carved and Acoustical Bamboo Wall Panels

Groove acoustic panel is the common sound absorption materials in modern buildings. The structure of groove in surface and perforation in back is base on scientific calculation and acoustic theories. The panel has excellent noise reduction and sound absorption performance, especially for medium and low frequencies.         

Horizontal/Vertical Bamboo Flooring Inspection Horizontal/Vertical Bamboo Flooring Inspection

Solid Horizontal/Vertical Bamboo Flooring

Main Specifications Material: Solid Bamboo Color: Natural/Carbonized Structure: Horizontal/Vertical Density: 0.72g/m3 Moisture content: 8-10% Hardness: 719kg/cm2 Formaldehyde≤0.20mg/l Impact resistance: 97.1kg/m2 Main Length: 915/960/1830/1860 mm, Main Width: 96/135/142/152 mm Main Thickness: 10/12/15/18 mm Loading: 1400 m2 with pallets for 1x20'FCL

Strand woven bamboo Strand woven bamboo

Strand Woven Bamboo Flooring

Mainly Specifications Material: Solid Bamboo with glue Color: Natural/Carbonized/Tiger/Zebra/Colored Structure: Strand Length: 920/1830/1850 mm Width: 96/135/140 mm Thickness: 12/14 mm Joint: T&G/Locking click

Glaze Strand Woven Bamboo Flooring Glaze Strand Woven Bamboo Flooring

Bamboo Flooring - Stained brushed on edge

Hand scrap surface with light brushed Stained brushed one surface Density: 1050kg/m3     

SPC qualified standards, quality control check list SPC qualified standards, quality control check list

SPC qualified standards, quality control check list

1.  Appearance & Quality Requirements Defects Items Standard Defects, fissures, wrinkles, holes Not allowed (a)Offset printing, delamination, peeling Not allowed (b)Spots, bubbles, scratches, discoloration etc. Not obviously (a) is suitable for heterogeneous floor (b) can be agreed according to the contract between the supplier and the buyer   Item Superior product Qualified product Frosting mark and water mark Not allowed  ≥ 3% the area of the board Scratches Not allowed Press mark Not allowed Previous spots of impregnated paper Not allowed Gloss unevenness Not allowed  ≥ 3% the area of the board Spots,dirt and similar surface defects Not allowed ≤ 10mm², 每米长允许一个allowable 1pc/m Blister Not allowed Bubble Not allowed Tearing of impregnated paper Not allowed Bare substrate spots due to defective surface covering Not allowed Fissure on the surface Not allowed Delamination Not allowed Tongue and corner deformity Not allowed   2. Size And Deviation Length  ≤ 0.1% of length Width ≤ 0.2mm, the difference between the maximum and minimum values ≤0.1 mm mm +0.13mm to -0.10mm,最大值与最小值绝对值不超过(maximum variation)≤0.1mm Straight Angle qmax≤0.20mm straightness smax≤0.20mm Height difference average value ≤ 0.10mm, Hmax ≤ 0.15mm Gap average value≤ 0.07 mm, Gmax ≤0.1 mm Model of click 应与确认的钢模相同should be the same as the confirmed steel model   3. Physical And Chemical Performance Requirements Gloss matte (3~10)±2° semi-matte (15~25)±2° glossy 25以上(more than 25)±2° Tensile Strenght 5cm/120N: 4.0mm≥100N 5.0mm≥120N Ply Adhesion 60N/5cm Curl after 6hrs at 80℃ Laboratory Oven for 6hrs&80℃ then measure with a Vernier: ≤1mm Dimensional Stability Laboratory Oven for 6hrs&80℃ then measure with a Vernier:≤0.1% Dimensional changes after heating WPC 65℃≤0.2%,SPC 80℃≤0.1% abrasion resistance  ≥0.015g/1000转(r) Abrasion resistance Paint film scriber ≥4B Surface scratch resistance Surface decorative pattern is not scratched under 4.0N's force. Indentation ≤0.05mm Formaldehyde release  No Formaldehyde Bibulous rate ≤3%     Packing Product Mark Before the products are stored, they should be tagged in proper parts with their product models, trademarks, production dates, etc.   Packing Mark The standard codes , factory name, address, product name, production date, trademarks, specifications, formaldehyde release sign, type, grade, quantity, etc.   Package A product shall be packed based on its category, specification and grade. The enterprises shall provide detailed instruction books and manuals according to the characteristics of a product. The package shall protect products from being hit,scratched or stained. Packing requirements shall only be settled after negotiation between two parties.

Professional China Floor Inspection Professional China Floor Inspection

CFI's Promise

Take the chance to choose our professional inspection services and avoid potential flooring problems and import risks!

OUR

NEWSLETTER

   

A free consultation

We focus on floor inspections only, we try to help you to solve all the questions in flooring line.